Bluonics 4 Stage Drinking Water Filter UV Ultraviolet Light ...

Author: May

Jun. 24, 2024

82

0

0

Bluonics 4 Stage Drinking Water Filter UV Ultraviolet Light ...

I purchased this Bluonics 4 stage drinking water filter to replace a 20+ year old single carbon block under-counter filter system that was becoming difficult to find filters for.

I hung the Bluonics filter system beneath the kitchen sink counter on a cabinet sidewall making certain to leave room below the canisters for filter element replacement and room above for UV lamp replacement.

CAUTION: To reduce possible hydrostatic damage and leaks, after installation but before turning on your water supply, open the filter's faucet to allow air to escape as the filter canisters fill.
It can take almost 2 minutes before you get water flow from the faucet. Run the filtered water for at least 5 minutes to remove loose carbon dust and air bubbles that will make the filtered water appear cloudy.

The Bluonics came with everything needed to install (including 3 filter elements, uv lamp system, fittings, tubing and faucet) except the mounting screws and 3/8 inch to 1/4 inch tubing adapter needed for my install.
I decided what I needed and purchased before attempting installation.

All connections to and from the filter are push-to-connect ( PTC, aka SharkBite).
My old filter was connected to a dedicated shutoff valve under the kitchen sink. The valve has a 3/8 compression fitting outlet. This filter's tubing is all 1/4 inch so I found a 3/8 to 1/4 PTC tubing adapter and connected to my existing 3/8 tubing. That adapter saved having to replace the shutoff valve.

The old filter output was also 3/8 inch tubing to the old faucet with a 1/4 inch icemaker tap.
I replaced the old 3/8 inch faucet with the included 1/4 inch faucet and purchased a 1/4 inch PTC tee which connected filter output to new faucet and icemaker inputs.

I read several reviews that complained about no way to connect the filter's 1/4 inch tubing to the included faucet. Unless the part was missing, that is not true.
The faucet input fits the 1/4 inch PTC coupling included in the parts bag. One end pushes onto faucet and 1/4 inch filter output tubing pushes into the other end.

Other reviews complained about not being able to determine filter input and output. Common sense would dictate that input goes into the first filter housing and output comes out of the UV lamp assembly.
NOTE: You will need to remove the tubing plugs from filter input and output by compressing the tubing release tabs.

Several reviews complained about leaks. I had zero leaks after installation. Each filter canister has a rubber o-ring. After installing each filter, tighten the canister by hand then use the included filter wrench to snug closed. Over tightening will deform the O-ring and cause a leak. Lubricating the o-ring with a compatible lubricant will add to its life.

The UV light housing gasket is tricky and the illustrated instructions only made sense after figured out I needed to push the knurled nut OVER the gasket and glass tube end.
Overtighening the nut will deform the gasket and leak. The extra o-ring was confusing and unnecessary but will work as a spare if needed.

I plugged the UV light ballast into a receptacle under the sink that I added when installing a new dishwasher a few years back in preparation for an eventual UV water filter. &#;

Be certain tubing pushes into all PTC connectors at least 1/4 inch or it will not lock. Make a mark on the tubing 1/4 inch from each end to help as it is possible to push in the tubing part way.
Pull on each connection after pushing tubing in. It should not come out unless you press in the tubing release.
BE SURE TO USE THE INCLUDED LOCKING RINGS ON EACH PTC CONNECTION to prevent accidental release of tubing.

As others have mentioned, the filtered water will come out warm for the first few seconds as the UV light is always on.
I read about some systems including a flow switch so the light only comes on when water flows but this one doesn't have it. Maybe a retrofit later but not worth the effort to build one in my opinion.

Our city water supply is chlorinated, fluoridated and tastes terrible, not to mention the invisible dead things killed by treatment. Most municipalities will recommend filtering their end product.
The filtered water has no detectable taste to me and is especially refreshing from the refrigerator's cold water dispenser.

I believe the flow rate was advertised as 1/2 gallon per minute but I'm getting at least a gallon per minute. A little less than my old filter but more than I expected from this one.

For added safety, we always turned off the water supply to our old filter if going on vacation and will continue that practice with this one.

At this point I am happy with this system and would recommend it.

Good luck.

Read more

Link to UVDF

Air Purifier with UV Light & True HEPA, Up To 500 sq. ft.

Very carefully. Oil from your fingers will reduce the performance of the UV light, so always use gloves or touch only the light&#;s metal area. Unplug the unit and turn it upside down. Remove the base and filter, then slowly loosen the GREEN screw. Grasp the wire connectors just under he bulb housing and gently disconnect it by squeezing the side and top notches. Holding the bulb housing straight up SLOWLY slide the UV bulb out of the housing to keep rubber protectors in place. Slowly slide the new bulb into the housing to fit into the top and bottom rubber protectors without forcing. Grasp wire connectors from the purifier and bulb housing to connect by pushing together. Re-attach bulb housing by tightening the GREEN screw. Insert filter and reattach base cover. For more information, please read the Use & Care manual.

If you want to learn more, please visit our website wholesale uvc kitchen faucet.

Comments

Please Join Us to post.

0

0/2000

Guest Posts

If you are interested in sending in a Guest Blogger Submission,welcome to write for us.

Your Name: (required)

Your Email: (required)

Subject:

Your Message: (required)

0/2000